- Mar 16, 2025
-
-
Add wireplumber config for fix low volume issue. Part-of: !6327 [ci:skip-build]: already built successfully in CI
-
Part-of: !6327
-
Part-of: https://gitlab.postmarketos.org/postmarketos/pmaports/-/merge_requests/6323 [ci:skip-build]: already built successfully in CI
-
Perhaps the biggest highlight of this release is addition of Qualcomm Sensor Manager support (thx @Tooniis). Several little impovements: * Notification LED support for clover, laevnder, tulip ( @setotau ) * missing SDCC block resets were added, several devices ( @alexeymin ) * missing SD card detect GPIOs were added, several devices ( @alexeymin ) * SD card instability was fixed, several devices ( @alexeymin ) * pd_mapper module now supports SDM630/636 ( @alexeymin ) * numerous dtbs_check warnings fixed, in preparation for upstreaming * several commits were dropped, they are now upstream! Manual config changes: * SNS_REG/SMGR modules were enabled * LED/QCOM_LPG modules were enabled FIXME: qrtr as a bus requires some kconfigs to be =y (for SMGR patchset): * CONFIG_QRTR=y * CONFIG_QRTR_SMD=y Signed-off-by:
Alexey Minnekhanov <alexeymin@postmarketos.org> Part-of: https://gitlab.postmarketos.org/postmarketos/pmaports/-/merge_requests/6321 [ci:skip-build]: already built successfully in CI
-
Paul Sajna authored
Part-of: postmarketOS/pmaports!6324 [ci:skip-build]: already built successfully in CI
-
- Mar 15, 2025
-
-
Package auto-update authored
-
- Mar 14, 2025
-
-
Casey authoredThis isn't used yet but will be required for SCMI cpu frequency scaling on X1 Elite. Let's get ready for that by enabling it now. Signed-off-by:
Caleb Connolly <caleb@postmarketos.org> [ci:skip-build] already built in CI Part-of: postmarketOS/pmaports!5814
-
Delete package - it was replaced with msm-firmware-loader. Part-of: postmarketOS/pmaports!6315 [ci:skip-build]: already built successfully in CI
-
Starqltechn required firmware to be pulled out of the particular phone. Replace starqltechn firmware package dependency with msm-firmware-loader. Part-of: postmarketOS/pmaports!6315
-
Part-of: !6319 [ci:skip-build]: already built successfully in CI
-
Jens Reidel authored
Signed-off-by:
Jens Reidel <adrian@travitia.xyz> Part-of: https://gitlab.postmarketos.org/postmarketos/pmaports/-/merge_requests/6318
-
- Mar 13, 2025
-
-
Package auto-update authored
-
Add starqltechn initfs modules, recently enabled in linux kernel. This provides touchscreen and haptics support when in initramfs. This allows to use onscreen keyboard in initramfs debug mode.
-
- Mar 12, 2025
-
-
Package auto-update authored
-
Part-of: !6294 [ci:skip-build]: already built successfully in CI
-
linux-lts from Alpine sets CONFIG_PSI_DEFAULT_DISABLED, so we need to enable it manually with the kernel cmdline. Part-of: !6303 [ci:skip-build]: already built successfully in CI -
linux-lts from Alpine sets CONFIG_PSI_DEFAULT_DISABLED, so we need to enable it manually with the kernel cmdline. Part-of: !6303
-
Part-of: postmarketOS/pmaports!6302 [ci:skip-build]: already built successfully in CI
-
Part-of: postmarketOS/pmaports!6302
-
These are no longer used, remove them. Part-of: !6248 [ci:skip-build]: already built successfully in CI
-
The thermal monitor measures an NTC thermistor which decreases voltage when the temperature increases. When fixing the scaling for the first time, a wrong division by 20 was removed. The voltage code was still high by a factor of 28900/16384, enough that the thermal monitor constantly signalled/interrupted at a low voltage/high temperature trip point. The thermal monitor still reports the correct temperature so the kernel keeps the wrong trip points and lets the thermal monitor keep interrupting 1000 times/sec. Fix the other scaling amount so the thermal monitor sends interrupts at the right temperature (with some imprecision).
-
- Mar 11, 2025
-
-
Package auto-update authored
-
Part-of: !6276
-
- Mar 10, 2025
-
-
Signed-off-by:
-
Signed-off-by:
-
Signed-off-by:
-
Signed-off-by:
-
Signed-off-by:
-
This also prepares a bunch of our changes for upstream and drops unsupported devices for now. They will be re-added when they have been tested to work at all. Signed-off-by:
-
- Mar 09, 2025
-
-
Upgrading from the old LTS (6.1.y) to the latest LTS (6.6.y) version. Kept most of the defaults, except where the current/previous config dictated another logical decision.
-
- Mar 07, 2025
-
-
Package auto-update authored
-
[ci:skip-build]: already built successfully in CI
-
- Mar 06, 2025
-
-
Package auto-update authored
-
- Mar 05, 2025
-
-
Package auto-update authored
-
Add some patches which finally fix mobile data on this SoC! https://lore.kernel.org/netdev/20250227-ipa-v4-7-fixes-v1-0-a88dd8249d8a@fairphone.com/T/ [ci:skip-build]: already built successfully in CI
-
Package auto-update authored
-
- Mar 04, 2025
-
-
[ci:skip-build]: already built successfully in CI
-
[ci:skip-vercheck] [ci:skip-build]: already built successfully in CI
-
-
-
